That's going to depend on the entry height and width of the cutout under the door of your 2018 Winnebago Micro Minnie 1808FBS, but based on the pictures I can find I kind of doubt anything more than a single step unit will work.
If you can send me the measurement from the top of the mounting cutout for the steps to the ground, and the width of that cutout I can check for you.
If you cannot fit another step then you'll just need to use a portable single step # SASXLA-09C-G which is adjustable... view full answer...
For your 2021 Winnebago Micro Minne 1800BH I recommend the Adco SFS AquaShed Cover for Travel Trailer - Up to 20' Long - Gray # 290-52240 which due to its Heavy-duty, 3-layer fabric protects that protects against rain, snow, and sun.
The side panels constructed of non-abrasive, triple-layer polypropylene that is breathable to prevent mold and mildew from forming, and the top is made of a triple-layer SFS AquaShed fabric that beads water to prevent it from pooling on your trailer, and protects... view full answer...
I looked up some pictures of your 2021 Winnebago Micro Minnie 1808 FBS and it has an Alumi-Tread pull out step so for a three step version you'd need the part # LC432696 and you'd be set. view full answer...
The Curt # C17499 TruTrack weight distribution system you'd looked at is designed for trailers with a fully loaded and ready to tow tongue weight ranging from 500-800 lbs, which is right around where your Micro Minnie would be.
In addition to the fully loaded tongue weight of the trailer, the weight of anything carried in the truck bed behind the rear axle should also be considered as tongue weight. Using a scale like the etrailer Tongue Weight Scale for Campers and Utility Trailers -... view full answer...
Thanks for the pictures! The 550 lbs spring bars you are using are too small and is causing the sagging in your Silverado's rear end. I looked online your 2022 Winnebago Micro Minnie Travel Trailer has a 6,000 lbs total weight capacity. Tongue weight is typically between 10% and 15% of your trailer's total weight.
It looks like you have a Blue Ox SwayPro system. I have listed both options of replacement spring bars below. Like you said you will want to load your trailer up and figure... view full answer...
For your 2020 Winnebago Micro Minnie 1808 FBS, I recommend going with the Adco Olefin HD RV Cover # AD97ZR.
This cover will work with travel trailers that are up to 20' long, is made from triple layer polypropylene, has built in vents to help reduce the interior buildup of mold and mildew, and will work great for winters in Montana. view full answer...
The Winnebago Micro Minnie 2108 DS measures 22'5" long so in order to find the correct storage cover we just need to subtract 3' for the tongue and round up. Therefore, we're looking at a cover for a 20' trailer and for this I recommend the Adco SFS AquaShed RV Cover for Travel Trailers up to 20' Long part # 290-52240 if you live in the north or the Adco Olefin HD RV Cover for Travel Trailers part # AD97ZR if you live in the north or south. These are both great options, the only difference... view full answer...
A 10 amp controller could easily handle a total of 155 watts of solar panel power so yes the Go Power Solar Flex Expansion Kit # 34280125 would work for you. view full answer...
Since it looks like you have C-channel on your 2021 Winnebago Micro Minnie FBS Comfort Explorer you'd have to find a welder to box the frame so that you can then install the Mount-n-Lock SafetyStruts # MO22FR that you referenced but it can fit. view full answer...
It is pretty common for the 3 step RV steps to be a couple inches wider than the 2 step options so I would not be shocked if the width of the Lippert steps # LC432696 being 27-1/2 inches is wider than what you have now. As long as you have the width needed for these to fit they would still work.
The brackets probably won't bolt right up so you could use the outriggers # LC301704 for new ones. view full answer...
Since you're unable to use the hitch at the back of your 2018 Winnebago Micro Minnie I recommend checking out the Gen-Y Hitch Replacement Shank # 325-GH-304 along with the Swagman Current Bike Rack # S64678.
The Gen-Y has a 7-1/2" rise and then the Current has an additional 8-1/2" of rise so the platform of the rack will sit about 16" above the hitch receiver on your vehicle. Hopefully this gives you enough rise to clear anything on the tongue of your trailer.
Attached are some videos... view full answer...
Yes, you can replace the assemblies of one axle on a tandem axle trailer without any issue. The Dexter Nev-R-Adjust Assemblies part # 23-468-469 are the correct set for your 2018 Winnebago Micro Minnie 2106DS since we know it has 3,500 lb trailer axles. view full answer...
The Wisight for Pre-Wired RVs part # ASA24YR that you referenced requires the a Voyager only connector that we can't get any type of adapter for so your best option would be the Furrion Vision S part # FOS43TASF which just needs to wire to the running light circuit of the trailer instead so if your RV wasn't pre-wired it would be the easier and better solution. The Furrion kits have the best signal and reception too which is why we recommend them so highly. view full answer...
Hey Charley,
The Lippert part number you gave me unfortunately isn't coming back to anything so it's likely an OEM only part number. That being said, we can still find a replacement for your trailer, we'll just need to get the entry height measurement, This is the height from the ground up to the top of the threshold. With your 24" width and the entry height we can find a compatible fit for your trailer. view full answer...
As long as the frame where a scissor jack like the etrailer.com # TJSC-24 has room to be mounted, there should be no issue replacing your current jacks. The base of the # TJSC-24 will measure 10-1/4" long by 3-1/4" wide, so as long as you have that kind of space you will be good to go.
However, it should be noted that this jack is designed to stabilize a portion of your trailer's weight and not to support the full weight of your trailer. Do not use this jack to lift your trailer or RV.... view full answer...
Since your GVWR is 7,000 lbs that would indicate most likely your tongue weight is going to be between 600-800 lb which would put you between two weight distribution systems but most likely the # BXW1000 would be your best bet as it has a 700-1,000 lb tongue weight range.
Now if you were going to come in on the lighter end of the spectrum the # BXW0750 would be the better choice as it has a range of 550 lbs to 750 lbs. Keep in mind that any cargo weight behind the rear axle of your tow... view full answer...
For a customized RV cover with the Winnebago Flying W logo on it, we have in stock the Winnebago Adco RV Cover, # 290-64843 with actual dimensions of 315" long x 100" wide x 96" tall. This is listed for Winnebago travel trailers 22'1" - 24'. While this may be a little longer than needed if yours is measured at 23' and 6", not including the trailers tongue, it has cinch ropes at front and rear of cover used to remove some slack. This also has straps secured under the vehicle to prevent... view full answer...
If you're prewired for Furrion then there will be a connector already there for the Furrion Vision S Wireless RV Observation Camera System w/ Side Marker Light Cameras - 5" Screen # FCE48TASL-05 to plug into.
If you don't have a shark fin camera mount on the back of your 2019 Winnebago Micro Minnie Travel Trailer then you're most likely prewired for Voyager camera systems. To work around this you can just remove the old mount or cover on your RV and use the wiring from part # FRCBRKT-BL... view full answer...
The outer brackets (hexagon heads) have changed with the Solera 5000 Series slide toppers so you'll have to slide them off of the inner brackets to install the Solera RV Slide-Out Awning # LCV000165062. You can leave the inner brackets mounted to the wall of your slide out and simply slide on the new outer brackets to get the slide topper installed.
On a side note, It looks like you might have slightly too big of a slide topper on the slide out and it's causing too much tension on the... view full answer...
So when we give fits for travel trailer covers, that does not actually include the length of the tongue, just the main body of the travel trailer. The correct fit for a cover for your 2021 Winnebago Micro Minnie 2108TB travel trailer will not include the tongue, so you can choose from one of the following options, depending on the climate you live in:
- Moderate Climates: Adco SFS AquaShed Cover for Travel Trailer # 290-52240
- All Climates: Adco Polypropylene Storage Lot RV Cover for... view full answer...
Go To Results